micro scale
Vortex
BabyDragon comp chassis spec
- Carbon Chassis
- Portal or Straight axles
- You need a forward motor mount plate (stock CR18P or SCX24 Furitek) for best results
- 12° angled skid
- RCMCCA class 2 and class 3 legal
Product contains
- Carbon fiber chassis rails
- PLA+ 3D printed parts
- SCX24 or CR18P skid
- High Clearance sliders for your esc/battery
- Front/rear body mount
- 2 optional esc/receiver/battery tray
- Does not contain hardware tools
Axial SCX24 and HobbyPlus CR18P ready
You can select your preferred skid version. The holes are drilled for SCX24 M1.4 screws, so you need to drill the required holes to 1.7mm.
BABYdragon spare and optional parts ( we will still upload in this week )
Black Carbon (PA12CF15 carbon nylon)
Light Blue
Nordic Orange
Peak Green
BabyDragon Chassis parts
4,99 €
3d printed BabyDragon skid for SCX24, CR18P or TRX4M transmissions. Please tighten the screws slowly, so that the material does not heat up.
Out of stock
BabyDragon Chassis parts
10,99 €
INJORA SCX24 33% Underdrive Diff Gears, 1/12T worm gear hardened steel material.
Out of stock
BabyDragon Chassis parts
10,99 €
INJORA SCX24 33% Overdrive Diff Gears, 2/12T worm gear hardened steel material.
Out of stock
BabyDragon Chassis parts
17,99 €
INJORA Stainless Steel Drive Shafts (Gladiator), D-Shaped hole design offer tighter connection to transmission and axles.
Black
Light Blue
Nordic Orange
Peak Green
BabyDragon Chassis parts
4,99 €
3d printed body mounts, esc and battery tray for BabyDragon. Please tighten the screws slowly, so that the material does not heat up.
Black
Light Blue
Nordic Orange
Peak Green
BabyDragon Chassis parts
4,99 €
3d printed sliders for BabyDragon. Please tighten the screws slowly, so that the material does not heat up.
SCX24 SETUP
For best performance and geometry results, use the gladiator or deadbolt front links/driveshaft, and gladiator rear links/driveshaft.
Check out our Team Driver, Tamas build guide for his BabyDragon setup.
Driveshaft length:
Deadbolt, B17: Front: 32.5-40mm
C10, JLU, Bronco, Gladiator: Front: 40-52mm
Gladiator: Rear: 65-95mm
Links length (eye to eye):
Deadbolt, B17: Front Upper: 29.5mm, Front Lower: 41mm
C10, JLU, Bronco, Gladiator: Front Upper: 39mm, Front Lower: 50mm
Gladiator: Rear Upper: 70mm, Rear Lower: 78mm
Overdrive/Underdrive: I’m using stock gears in front (2/16T) and 33% underdrive in rear (1/12T).
HOBBYPLUS CR18P SETUP
The holes are drilled for scx24 M1.4 screws, so you need to drill the required holes to 1.7mm. You can use the stock links/drive shaft, but for better performance you need to create your own links. You can use the SCX24 driveshafts too, I recommend the size below.
We have 2 skid options, for 1 gear and for 2 gear transmissions.
Check out our Team Driver, Tamas daughters build guide for her CR18P based BabyDragon setup.
Driveshaft length:
Front: 40-52mm (SCX24 C10 front)
Rear: 60-90mm (SCX24 Deadbolt rear)
Links length (eye to eye):
Front Upper: 39mm
Front Lower: 49mm
Rear Upper: 64mm
Rear Lower: 76mm